Search found 23 matches

Go to advanced search

by BULLDOG
Sun Sep 06, 2015 9:39 pm
Forum: General Discussion
Topic: Just for fun: whats the largest machine you have seen?
Replies: 5
Views: 1515

Just for fun: whats the largest machine you have seen?

Hallo folks, what's the name of the largest CNC machine that you have seen? not on the internet, that would be too easy, i mean really seen with your own eyes? I once saw a 2.5 meter long Badog CNC http://www.badog.ch at EPFL in the architecture department in Lausanne Switzerland
by BULLDOG
Sun Aug 09, 2015 4:18 am
Forum: Milling, tooling and engraving advice
Topic: Wood Engraving Problem
Replies: 6
Views: 1001

Re: Wood Engraving Problem

I am not getting your question. You have said that the lettering is 1.2 cm tall. Do you mean that you have engraved the background so that the letters stand out tall, or that you have carved the letters 1.2 cm deep into the wood? In the first scenario, I think I will be equally as dumbfounded as you...
by BULLDOG
Wed Jul 22, 2015 4:12 pm
Forum: DIY cnc machines and Builds
Topic: USB vs Ethernet motion boards
Replies: 1
Views: 306

Re: USB vs Ethernet motion boards

That depends on your needs. The Smoothsteppers are by far the most popular. The USB and Ethernet motion boards are similarly priced so that is not a factor here. The KFLOP is also supposed to be very good, but is probably a lot more complex to setup.
by BULLDOG
Sun Jul 12, 2015 10:48 am
Forum: Other machines, tools and gadgets
Topic: Multicam router fault
Replies: 2
Views: 633

Re: Multicam router fault

Hey, have you resolved this issue?
by BULLDOG
Mon Jun 15, 2015 8:15 am
Forum: Milling, tooling and engraving advice
Topic: Why does BobCad machine an area when it shouldn’t?
Replies: 10
Views: 887

Re: Why does BobCad machine an area when it shouldn’t?

You need a little bit of knowledge to complete your project. However, it shows you mixing up some functions and barely relying on some assumptions, to finish up the project. There is training for this, available for purchase - either bundled with the annual support package or at an hourly rate. Our ...
by BULLDOG
Thu May 21, 2015 3:08 am
Forum: Other technical advice
Topic: Machineable Wax
Replies: 6
Views: 1207

Re: Machineable Wax

I absolutely LOOOVE this wax. Clean, non fussy and snappy. Just like jazz
by BULLDOG
Thu May 21, 2015 3:04 am
Forum: General Discussion
Topic: What are these?
Replies: 39
Views: 2568

Re: What are these?

this technology is really good, but I feel like it has led loss of fine art by hand. There is an expert with the talent to produce such fine art, but their services can never be required again because of this machines.
by BULLDOG
Tue May 19, 2015 3:09 am
Forum: Other technical advice
Topic: Which is better between EDM and CNC?
Replies: 48
Views: 3395

Re: EDM CNC DISCUSSION

I am surprised no one has talked about the process. EDM machining uses graphite which is favorable for these metal cutting. It is not affected by high temperatures, cheaply available and available in large qualities and resistant to wear.
by BULLDOG
Mon May 18, 2015 3:51 am
Forum: Milling, tooling and engraving advice
Topic: What is the difference between Mould casting and resin casting?
Replies: 8
Views: 1318

Re: What is the difference between Mould casting and resin casting?

Always exercise proper care while doing the casting using resins. This stuff is potentially lethal and fumes may be poisonous or harmful, since they may get into the body and act as carcinogens. Be very careful while dealing with them. Use this guide:http://www.resinobsession.com/Resin-Resin-Resin/1...
by BULLDOG
Thu May 14, 2015 7:21 pm
Forum: Other technical advice
Topic: Help I have a router accuracy problem
Replies: 8
Views: 684

Re: Help I have a router accuracy problem

‘I hope your manufacturer has the solution this time. Your machine has warranty so maybe it is best if they take back the machine and send you another while they try to fix the issue. Seriously, what if you have a lot of work piled up or customers are streaming in from your services. I am trying to ...

Go to advanced search



  •  The team

  •  Search
  • Advanced search


  •  Top Posters

  •  Newest members

  •  Who is online?




 

 

cron